Welcome to Naveen Ceramic & Vitrified Tiles

India's No. 1 Ceramic & Vitrified Tiles
Ceramic & Vitrified Tiles
Naveen Complex,

7th and 8th Floor,14, M.G.Road, Bangalore – 560001

Ceramic & Vitrified Tiles
Send your mail at


Ceramic & Vitrified Tiles
Have any question?


Cleaning Tiles After Renovation

Are you thinking of remodeling your home? If so, washing the tiles will be one of the several tasks you must complete. To get the best results, you should use particular techniques and products, so it’s more challenging than just giving them a quick scrub. Here are the ways to get the best results.


To clean grout and other filth accumulated on ceramic tiles, combine the following ingredients:

  • The T-shaped spatula or rubber scraper.
  • Hoover
  • A felt object.
  • Vinegar or ammonia.
  • An antimicrobial component.
  • Gloves.
  • Little brush (toothbrush).
  • Use an alkaline gel or a specialized ceramic tile cleaning (dishwashing liquid Cinderella, Cillit window cleaner, soap, and water are all acceptable).

Cleaning Mechanically

After installation, the tile’s surface still shows signs of grout and dust. As a result, before cleaning the tiles, any mortar chunks should be taken out.

Dust and filth should be removed with a hoover. Use a trowel to remove any leftover grout or primer. While doing this technique, take care not to damage the coating. Once all the tiles have been removed, use your feet to rub the surface very hard. Reclean both sections after the tiles have dried.

Thoroughly Clean

To ensure that all tiles and seams are pristine after cleaning, you must thoroughly wash the entire surface.

  • Take a breather with steam to clean the bathroom tiles before work. Open the hot water faucet, shut the doors, and then step away from the bathroom for around 30 minutes.
  • Mist the tiles with the detergent.
  • Use the bottles with the spray gun if it’s a specialized product.
  • Make sure to wet the surfaces with sponges if the substance is soap or another solution.
  • Use a rag to wipe away filth from the surface.
  • Clean the joints using a gel, non-abrasive powder, and a soft bristle brush to remove dirt between the tiles.
  • Wash away any detergent traces after cleaning the fabric with fresh water. Apply an antibiotic to the joint once the surface has dried to prevent the growth of fungi.
  • Be careful not to use harsh or acid-based hydrochloric powders to clean your tiles. The glaze’s caustics and abrasives may cause damage.
  • Ensure the air circulation in the room is adequate if you’re using chemicals that foam, and stay away from chemical vapors.

Steps to remove white haze

As a consequence of installing tile, white haze (also known as grout haze) is the grout that has films over the tile surface during installation and the drying process. When tile grout dries, minerals stay on the surface of your freshly laid tile since tile grout is formed of cement and minerals combined with water.Start by using your grout sponge and water to remove the grout haze. If it doesn’t work, grab your grout float and run it over the area while it’s still wet. By doing so, the grout haze may be forced into the cracks between the tiles. Continue doing this until the haze is gone. Check for any more white haze after buffing the area with cheese cloth until it is completely dry. Repeat the technique if you still see any, although you might need to apply grout haze cleaning. Most manufacturers advise using one gallon of lukewarm water with three ounces of grout haze cleaning. If the product becomes too cloudy, you might need to change it.

An Organic Method

There is a straight forward, natural method to try if you want to try and use something “green” to clean your grout haze after remodeling your bathroom.

Combine a solution of two cups of water, one cup of baking soda, one cup of ammonia, and two cups of white vinegar.

To remove the haze, use a sizable sponge to wipe as you would with a grout haze cleaner.

If there is a Colour Difference

After cleaning the tiles, dirt and soap will be visible on the flooring. Use a mild vinegar solution to gently wipe the surface of the tiles are dry but have smudges or marks.

Even with the most modern information and equipment, washing tiles after a renovation of your home could be a time-consuming task.  If you are planning on remodeling your home, connect with our experts at www.naveentile.com to get started.